Services

Your expert for PROFINET and industrial networks

Helmholz Benelux is the official PI Competence Center (PICC) in the Netherlands. Our network engineers review designs, commission and certify PROFINET and PROFIBUS networks, troubleshoot on site and give advice by phone or online, according to the PI guidelines.

  • Neutral design reviews and second opinions, before you build or extend
  • Commissioning and certification of PROFINET and PROFIBUS networks
  • Troubleshooting on site, often at short notice, with a report on the cause and advice
  • Design review, troubleshooting and advice for Industrial Ethernet, CAN bus and AS-i as well
  • Official PI Competence Center, audited by PI for PROFINET and PROFIBUS

Go straight to

Selection

Which service do I need?

ServiceChoose it when
Network design reviewYou are planning a new network or an extension, or want a second opinion on an existing design
Commissioning and certificationYour PROFINET or PROFIBUS network is installed or extended and you want proof that it meets the PI guidelines
Troubleshooting on siteDevices drop out, a station does not start up or a machine is at standstill
Periodical network checkupYou want to follow how your PROFINET or PROFIBUS network performs, with a report every three months
Advice by phone or onlineYou have a question about a topology, a component or a fault you cannot place

Network design review

A reliable network starts with the design. We check your design against the PI guidelines before the first cable is laid, or before you extend an existing plant, for PROFINET, PROFIBUS, Industrial Ethernet and CAN bus networks.

  • A check of topology, cabling, components and network load
  • Neutral advice, or a second opinion on an existing design
  • The consequences of each choice, with alternatives
  • Documentation according to the PI guidelines

What we check first

Most intermittent faults we find on site start in the physical network or in the design. In a review we check these points first, against the PI design guidelines:

PROFINET

  • Cable type per movement: Type A fixed, Type B occasional movement, Type C drag chains and robots
  • Copper links up to 100 m between two devices, fibre for longer distances
  • A ring with MRP where a long line would depend on every device in it
  • IT traffic, cameras and multicast kept apart from the cyclic PROFINET frames
  • Managed switches wherever faults must be found quickly

PROFIBUS

  • Segment length per bit rate: 100 m at 12 Mbit/s up to 1,000 m at 187.5 kbit/s
  • Up to 32 stations per segment, repeaters included
  • Exactly two powered terminators per segment, at the first and last node
  • Repeaters or active dropcables instead of stubs

Commissioning and certification

As a PICC we commission and certify PROFINET and PROFIBUS networks: we verify that the network and its documentation meet the PI guidelines and certify the installation, at first installation, after an extension or during a regular check.

  • Verification of the installation and documentation against the PI guidelines
  • A certificate as proof that the network meets the international PI standard
  • A documented reference that makes later fault finding and extensions easier

Network troubleshooting on site

Devices that drop out, a station that does not start up or a machine at standstill: our engineers come on site, often at short notice, find the cause and fix it, in PROFINET, PROFIBUS, Industrial Ethernet and CAN bus networks.

  • A systematic approach with bus monitors, analysers, testers and oscilloscopes
  • The cause found and fixed, from simple to complex faults
  • A report on the cause, the state of your network and advice to keep it reliable

Machine at standstill? Call us directly on +31 85 4010 710.

Network diagnostics

Measure it yourself

Cable testing, PROFINET diagnostics, traffic analysis and permanent monitoring: choose the right tool for your network.

Workshop

PROFINET troubleshooting and commissioning (NL)

Learn how to find and fix faults in PROFINET networks and which diagnostic tools you need, explained along the PI guidelines.

Periodical network checkup

With a periodical checkup you know at all times how your PROFINET or PROFIBUS network performs. The plan runs for a year: we install a network monitor and report on the state of your network every three months.

  • A PROFINET or PROFIBUS network monitor, installed in your network
  • A first check of the overall state of your network, with improvement points
  • After three months: an analysis of the monitor data, with a report
  • From then on every three months: an updated report and advice

Permanent diagnostics

Monitor your plant yourself

Cabinet Guard, Ethernet Cable Guard and PROFINET TEST TOOL Online monitor cabinet, cables and network continuously.

Advice by phone or online

A question about a topology, a coupler in your PLC project or a fault you cannot place? Our engineers answer it by phone or in an online session, according to the PI guidelines.

Schedule a call via the contact form, by email or on +31 85 4010 710.

Services per network

Each network page has its own services section, next to the components and the faults we find most often in that network.

PROFINET
PROFIBUS
Industrial Ethernet
CAN bus

PI Competence Center

PROFIBUS & PROFINET International (PI) recognises Helmholz Benelux as the official PI Competence Center in the Netherlands for PROFINET and PROFIBUS. PI audits every PICC on technical competence and on the quality of its service.

Frequently asked questions

Your question not listed? Ask us directly. The PI installation guidelines for PROFINET and PROFIBUS are available from PROFIBUS & PROFINET International.

What does a design review include?

We check the topology, cable types, link lengths, network load and components of your design against the PI guidelines. You get neutral advice or a second opinion, the consequences of each choice with alternatives, and on request documentation according to the PI guidelines.

How quickly can you come on site?

Often at short notice. For a machine at standstill, call +31 85 4010 710. We bring bus monitors, analysers, testers and oscilloscopes, fix the cause and leave a report on what caused the fault, the state of your network and advice to keep it reliable.

What does a periodical checkup include?

A one-year plan for PROFINET and PROFIBUS networks. We install a network monitor, check the overall state of the network and give improvement points. After three months you receive an analysis of the monitor data with a report, and from then on an updated report and advice every three months.

Do you also support Industrial Ethernet, CAN bus and AS-i?

Yes. For Industrial Ethernet, CAN bus and AS-i networks we review designs, troubleshoot on site and give advice by phone or online. Commissioning and certification according to the PI guidelines, and the periodical checkup, are for PROFINET and PROFIBUS networks.

Can I learn to troubleshoot PROFINET myself?

Yes. In our workshop PROFINET troubleshooting and commissioning you learn how to find and fix faults, which diagnostic tools you need and how to maintain a PROFINET network, explained along the PI guidelines. See all trainings and workshops.

What is a PI Competence Center?

A PI Competence Center (PICC) is recognised and audited by PROFIBUS & PROFINET International (PI) for its technical competence and quality of service. PICCs give independent support in planning, training and troubleshooting of PROFINET and PROFIBUS networks. Helmholz Benelux is the official PICC in the Netherlands.

Can you certify our network?

Yes, PROFINET and PROFIBUS networks. We verify that your network and its documentation meet the PI guidelines and certify the installation: at first installation, after an extension or during a regular check. The certificate is your proof that the network meets the international PI standard.

Which PI guidelines do you work with?

For PROFINET the Design Guideline (order no. 8.062), the Assembling Guideline (8.072) and the Commissioning Guideline (8.082). For PROFIBUS the Design Guideline (8.012), the Assembling Guideline (8.022) and the Commissioning Guideline (8.032). All are available from PROFIBUS & PROFINET International.

Show all 9 questions
Is your advice independent of brands?

Yes. As a PICC we give neutral advice according to the PI guidelines, also for networks built with components from other manufacturers.

Help with your network

Planning a new network, commissioning an installation or chasing devices that drop out? Tell us which network and devices you work with, and we will help you choose the right service.