netX 52 Chip Carrier incl. transformer – Real-Time Ethernet slave

Name: netX 52 Chip Carrier incl. transformer - Real-Time Ethernet slave
SKU: 767x.100
Availability: InStock

Real-Time Ethernet solution in the smallest space

The rapid and secure alternative to a slave interface developed by the customer is netRAPID. The compact, stamp-sized, 32 x 32 mm netX Chip Carrier is a solution that offers adequate costs per unit, a reduced risk, and a fast time-to-market. Like a standard QFP component, it will be soldered directly to the host system – by hand or SMD production process.

Optimized for minimum space requirements, netRAPID 52-RE contains all necessary operating components, such as Ethernet transformers, SQI Flash, and netX multi-protocol chip. Real-Time Ethernet communication is in focus. The protocol stack will be executed in the internal RAM of the netX. Thus, the hardware developer only needs to integrate network connectors, LEDs, and address switches on the host system. For the host system, a simple 2-layer printed circuit board is sufficient. The application development is reduced to the use of the API of the netRAPID.

To be able to profit from the full function of netRAPID, the licensed firmware must be acquired once and loaded during the manufacturing process.

Complete slave interface in the smallest space
Integrated transformers are used to save a lot of space
Host connection via dual-port memory or SPI
One hardware for all Real-Time Ethernet systems

Vraag direct een offerte aan!

netX 52 Chip Carrier incl. transformer – Real-Time Ethernet slave

Neem contact op voor de actuele levertijden.

Meer informatie aanvragen

Product	Product name	NRP 52
	Part number	7670.100
	Brief description	Chip carrier with Ethernet interface
Network controller	netX	netX 52
Integrated Memory	RAM	4 MB serial Flash EPROM
Power supply and current	Supply voltage	+3,3 V DC ± 5 %
	Maximum current (typically)	520 mA/600 mA (at 3,3 V)
	Power consumption (typical)	1.8 W
Host interface	Type	Parallel dual-port memory or serial dual-port memory (SPI, mode 3)
	Connector	76-pin solder contacts 1 mm with 1.5 mm grid
	Dual-port memory size	16 KB (14 address lines)
	Width for the data access to the dual-port memory (DPM)	8 or 16 bit
	Baud rate (serial dual-port memory)	Max. 50 MHz
Communication interface	Communication standard	Ethernet
	Interface type	100BASE-TX or 10BASE-T, isolated
Diagnostic interface	Type	USB or UART, the support of the diagnostic interface depends on the loaded firmware
	Connector	USB or UART: Signals at Chip Carrier, available only if integrated in host system
Display	LED displays	SYS System status
		COM0, COM1 Communication status
		2 x Link and 2 x Activity
Permitted ambient conditions	Ambient temperature range for operation	-20 … +70 °C (at an airflow of 0.5 m/s)
Device	Dimensions (L x W x H)	32 mm x 32 mm x 4 mm
	Weight	approx. 4 g
Conformance with EMC directives	Emission	EN 55011:2009 + A1:2010 Class B (Conducted), A (Radiated)
	Electrostatic discharge (ESD) according to IEC/EN 61000-4-2:1995 (Contact discharge method)	6 kV Criterion A
	Radiated RF, according to IEC/EN 61000-4-3 and IEC/ EN 55011 80-1000MHz, 10V/m, 80% AM / 1kHz	Class A
	Radiated RF, according to IEC/EN 61000-4-3:2006 1.0-2.7 GHz, 10V/m, 80% AM / 1kHz	Class A
	Fast transient interferences (Burst), according to IEC/EN 61000-4-4:1995 (Communication and data lines)	2.2 kV Criterion B
	Surge voltage, according to IEC/EN 61000-4-5:1995 (Communication and data lines)	1 kV Criterion B
	Conducted RF, according to IEC/EN 61000-4-6:2009 0,15-80 MHz, 80% AM / 1kHz	Class A